Then fiddle with the wire until its clipped back into place. Have a small cup ready to capture 1 ounce of oil. If you have changed the fuel filter on a 2000, you might have forgotten to put the rubber grommet between new fuel filter and fuel pump look at your old fuel filter. There is a little gap between 2 screws 10mm size, star connecting fuel injector to engine. What could be the problem please help? Be sure to remove the negative battery cable first and when you jack the car up support it with stands and use chocks for the wheels. Installation is the reverse of the removal process. Check the fuel system for leaks.
If the car doesn't start, then you probably have something more wrong than the starter. For vehicles equipped with a key system: 1. The shut-off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt. If no, then problem is again the relay. Then problem relates to computer. Underneath thereis a strut in the way take off the two bolts and push it aside and remove the oil filter small tub to catch a bit of oil isneeded , unplug the one connection to the solenoid and unbolt thewire from the rear of it.
Below is the manual instructions to restart pump should you have a minor collision. Then place the jack stands under the frame supports. Feb 24, 2016 Fuel inertia switch stops the fuel pump running in the case of a collision causing a broken fuel pipe which otherwise could spray a litre of petrol every few seconds and rather spoil someone's day. Loo … ks like it was made from an old coat hanger. I think it's quite a distance from the battery, but I'm unsure.
It's a small, inconspicuous part. Scrape the old Gasket off, if any. You take the bolts out of it. Its a tad tricky to get it to unhinge, but it will pop open. To find it easier on this, and all other vehicles, just follow the positive cable line that comes off of your … car's battery.
An inoperable fuel pump or blown head gasket can cause starting problems as well. This and other details can find in Hope helps. The only thing that stinks about having your local auto parts store bench-test it, is if the starter motor is good. During a collision or vehicle rollover, electrical contacts within inertia switch open, shutting off fuel supply to electric fuel pump. One is accessedbest from under the car. You will need a floor jack and two jack stands. Answer I have found that the inhibit relay sits in black relay box on the right side of the engine causes a lot of starter failures.
These two bolts hold in the starter. First thing get voltage at fuel pump relay checked, is there 12 volt to the relay. In the event of a moderate to severe collision, this vehicle includes a fuel pump shutoff feature that stops the flow of fuel to the engine. Suggestion 3: To get to the starter motor, to test it, you'll need to raise your Nissan up in the air. It goes through the cowling and screws into the top hole on the starter.
The cable attached to the positive terminal on the battery links directly to the starter. Then, get under the car, and disconnect the electrial connector easier with a slotted screwdriver Then using a 12 or 14mm socket, remove the bolt you can see mounting the starter to the engine. The other bolt is easily reached fromon top of the engine. Choose a flat and level surface to place the car on. All the lights come on, the radio, all the oil engine, brake lights come on the dash. It is the same bolt that the battery groundis attached to. Scrape the old Gasket off, if any.
Suggestion 2: All the tests, in this tutorial, need to be done with a fully charged battery in your Nissan vehicle. Next, put the new oil filter on the car. I am just a college girl and I figured out how to change my starter. They are placed on a diagonal, approximately 4 inches apart. Also, Chiltons refers to labeling the wires before removing the starter. Just need to depress the switch till you hear a click.
The hardest part is disassembly of the intake housing to get to the bolt heads for starter removal. Also, Chiltons refers to labeling the wires before removing the starter. In this tutorial I'll walk you, in a step-by-step manner, thru' the entire starter motor testing process. After the oil has drained into the pan. I would start by calling your local Nissan Dealership.